Introduction

It’s very annoying to discover that you can’t get your car to turn over. Your vehicle’s ignition system may be malfunctioning if you’re having trouble starting it.

Problems with the ignition can be very worrying and will definitely slow you down in your daily routine. Because we understand how challenging it is to deal with this issue, we have revealed the most crucial methods for addressing it.

Ignition Issues That Frequently Arise

Error Caused By A Defective Ignition Coil, Spark Plug, Or Wires Connected To The Ignition

Ignition problems can be brought on by a malfunctioning ignition coil, a non-functioning spark plug, or a damaged spark plug wire set. Having a properly functioning ignition system is essential to maintaining a healthy engine. 

Most vehicles will display a Check Engine Light (CEL) for a misfire if there is a problem with the spark plugs, which can cause a rough ride, engine misfires, and possibly lower gas mileage. 

In many cases, this problem can be fixed by simply replacing the faulty component. Altering the ignition coils and wires is a simple task. For some uses, however, the upper intake plenum manifold must be removed. 

You can find more detailed instructions for fixing your car in a repair manual. Here, we detail the steps you should take when testing your ignition coils or identifying problems.

A little extra care may be needed for the spark plugs in some vehicles. Depending on their location, some can be easily accessed and replaced, while others can be a lengthy and complicated undertaking. 

When it’s time to change the spark plugs, we have a handy manual. Some spark plugs require anti-seize and gapping before installation, while others do not. 

Find out what the spark plug maker recommends. Always use a spark plug socket when replacing spark plugs, and make sure to apply the correct amount of torque.

Deficiency In The Crank Position

The precise timing of firing the ignition coils is an essential component of any modern ignition system that does not employ a distributor. A crank position sensor, which is essentially a magnetic trigger, is used for this purpose. 

The sensor detects a trigger point in the crank’s rotation at just the right instant in the revolution and transmits a signal. It is impossible to recover this signal once this sensor has failed. 

 

 

Sometimes the component fails completely, leaving you with a non-running or non-starting vehicle. Sometimes the issue is episodic, resulting in misfires or stalling. Crank position sensor fault codes are typically detected by the engine computer at this point.

Ccd Cam Position Sensor

A cam position sensor is similar to a crank position sensor, except it monitors the camshaft(s) in an engine instead of the crankshaft(s). 

These parts analyse the cam’s position in relation to the ignition timing and either advance or retard the spark depending on its readings.

Misfires, low power, poor gas mileage, and the inability to start or run the engine are all symptoms of a faulty cam position sensor. 

When there is a problem, the engine computer will notice, as it does with most sensors, and display an error code.

Pick-Up Coil For Distributors

In distributor-style ignition systems that do not use breaker points, a pick-up coil or hall effect sensor (same thing) reads a cog wheel within the distributor to determine the precise moment to send a signal to the coil to fire.

When a pickup coil fails, the vehicle will not start. The pickup coil is more likely to be the source of the problem than the ignition coil. Because the distributor must often be taken apart in order to gain access to the coils, changing them can be a hassle.

Module Igniter

A lot of newer cars don’t have ignition modules anymore; instead, the function is located in each individual coil or the car’s onboard computer. For many electronic ignition systems, ignition modules were the norm from the late 1970s to the early 2000s. 

The unit is also known as an ignition control unit or power output stage control on some foreign vehicles.

In a distributor system, these components help process the signal from the crank position sensor or pick-up coil and send it to the appropriate ignition module. When they fail, you may experience a misfire, faulty coil packs, or the inability to start the engine.

Focusing In On The Problem

It is essential to keep in mind that a misfire can be caused by a wide variety of other vehicle sensors and situations that are unrelated to the ones listed above. 

It’s also possible for problems to originate from other, less obvious areas, such as fueling, vacuum, or engine timing. Before replacing any of these parts, make sure to check the electrical connections and wiring thoroughly for any signs of damage or shorts.

 

Conclusion

These days’ ignition systems are made up of a wide range of high-tech, sometimes finicky parts. A poor or non functioning vehicle is the result of a malfunction in any of the system’s components. Get to the bottom of your car’s ignition issues with the help of Revive Auto Repair.

FAQ

What Are Some Common Ignition System Problems?

Having a properly functioning ignition system is essential to maintaining a healthy engine. Most cars will display a Check Engine Light (CEL) for a misfire if there is a problem with the spark plugs, which can lead to a rough ride, engine misfires, and possibly lower gas mileage.

What Are Failures In The Ignition System?

When the engine is unable to light the incoming gas mixture and burn it, the ignition system has failed. Insufficient sparks are being produced, for whatever reason, to ignite the gas and turn the internal cylinders.

What Are The Factors Affecting Ignition?

The ignition delay is affected by primary factors like injection pressure, compression temperature, pressure, and air velocity, which are all influenced by engine operating variables like speed and load. 

It has been determined that compression temperature and pressure are the primary factors under typical operating conditions.

Is There A Fuse For The Ignition?

One of the most crucial electronic relays in a modern car is the ignition relay. It is responsible for supplying power to the vehicle’s ignition system and some components of the fuel system. It is typically housed in the fuse and relay panel under the hood.

Revive Auto Repair

2888 E Maple Rd, Troy, MI 48083
Phone: 248-817-5370
https://www.ReviveAutoRepair.com
Call or go online to make appointment